The comparative study of the influence of the parameters of the technological process of abrasive flow machining of the nozzle holes of the fuel injectors on the performance of the injection system
Article Sidebar
Main Article Content
Abstract
Improving the performance of automobiles is achieved by ensuring the optimal spraying characteristics of the mixture in the combustion chamber, which is achieved by changing the geometric parameters of the fuel flow of the fuel fluid through the nozzle. To obtain good energy performance of thermal engines in order to reduce pollution, it is used as processing operation (finishing and rounding) of the entrance to the fuel injector nozzle hole, erosion processing. Hydroerosion processing is carried out by removing the material to the erosive particles that are suspended in a working fluid, as a carrier.
From the analysis of this process it follows that the reduction of cavitation, the rounding of the nozzle inlet can reduce the wear caused by the diesel flow when the injection system is in operation and implicitly the reduction of the impact of pollution on the environment.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Bernd Ofner. Dieselmotorische Kraftstoffzerst¨aubung und Gemischbildung mit Common-Rail Einspritzsystemen, doctoral thesis, Technical University of Munich ,2001
F. Payri, R. Payri, F.J. Salvador, J. Martínez-López. “A contribution to the understanding of cavitation effects in diesel injector nozzles through a combined experimental and computational investigation, Computers & Fluids,” 58 88–101,2012, https://doi.org/10.1016/j.compfluid.2012.01.005
F. Yan, Y. Du, L. Wang, W. Tang, J. Zhang, B. Liu, C. Liu. “Effects of injection pressure on cavitation and spray in marine diesel engine,” International Journal of Spray and Combustion Dynamics, Vol. 9(3) 186–198.2017, DOI:10.1177/1756827716672472
Mohammad Nikouei. ,, Cavitation in Marine Diesel Applications Effects of Hydro-erosive Grinding on Flow and Nozzle Geometry”, Master of Science Thesis, Department of Mechanics and Maritime Sciences Chalmers University of Technology,2018, https://odr.chalmers.se/server/api/core/bitstreams/12baa69a-d26c-417d-b638-d577fda940a9 /content
S. Kampmann, B. Dittus, P. Mattes, and M. Kirner.The influence of hydro grinding of VCO nozzles on the mixture preparation in a DI diesel engine, SAE Paper 960867, 1996, DOI:10.4271/960867
Baddock, C., Wirth, R., Kampmann, S., and Tropea, C..The influence of hydro-grinding on cavitation inside a diesel injection nozzle and primary break-up under unsteady pressure conditions. In Proceedings of the Fifteenth Annual Conference on Liquid atomization and spray systems ILASS-Europe, 99, Toulouse, France, 99, 5–7.1999
POTZ, D., CHRIST, W., DITTUS, B..Diesel Nozzle – The determining interface between injection system and combustion chamber. Proceedings of Thiesel Conference, Valência, Espanha, Pages 133 – 138, 2000.
Deepak, D., Anjaiah, D. and Sharma, N.Y.. Numerical analysis of flow through abrasive water suspension jet: The effect of garnet, aluminium oxide and silicon carbide abrasive on skin friction coefficient due to wall shear and jet exit kinetic energy, International Science Index, Vol.6 (10).2012`
Fang, L., Zhao, J., Sun, K., Zheng, D. and Ma, D. Temperature as sensitive monitor for efficiency of work in abrasive flow machining, Wear, Vol. 66, pp. 678-687, 2009.
Weickert, M., Sommerfeld, M., Teike, G., Iben, U..Experimental and numerical investigation of the hydroerosive grinding. Powder Technology, Volume 214, Pages 1-13,2011, https://doi.org/10.1016/j.powtec.2011.07.013